Tag Archives: shaft collar

China Electric Motor Worm Gear Screw Jack Translating Screw With 6500MM Long Stroke screw shaft collar

Gearing Arrangement: Worm Gear,Worm Shaft,Lifting Screw
Rated Power: Max 16.5 KW
Input Speed: MAX 1500 RPM
Output Speed: MAX 1500 RPM
Model Number: RN-05T-RN-100T
Dynamic loading: 0.2T-26T
Static loading: 0.5T-100T
Protective: steel cover,rubber bellows,hand wheel
Installation: Upright or inverted
Speed ratio: According to youre requirment
Packaging Details: export standard plywood case
Port: HangZhou

Electric Motor Worm Gear Screw Jack Translating Screw With 6500MM Long Stroke
Specification1.Warranty:12 months2.Delivery:7-15 working days after deposit
Electric Motor Worm Gear Screw Jack Translating Screw With 6500MM Long Stroke Picture:

Features:

Model	RN-0.5T, 1T, 2T, 3T, 5T, 10T, 15T, 20T, 30T, 40T, 50T, 100T
Load Capacity	0.5 ~ 100 TONs
Travel Stroke	10 ~ 6500 MM
Screw Type	Translating Screw, Keyed Screw, Rotating Screw
Configurations	Self-Locking Trapezoidal Screw,Worm Gear,Worm Shaft,Taper Roll Bearing,Housing,Grease Oil Sealing etc.
Mounting	Upright, Inverted
Top End	Top Plate,Clevis End,Threaded End,Plain End and Forked Head
Functions	Lifting, Lowering, Pushing, Pulling and Rolling Linear Motions
Arrangements	Single Unit, In Pairs or Multi-Units Arrangement Available
Power Source	Electric Driven,Manual Operated or Both Are Available
Accessories	Protective Tube, TT motor factory custom 030 high speed long life dc brushed motor for RC toys Rubber Bellows, Electric Motor, Hand Wheel, Inverter, Limited Switches, Linking Shaft, Coupling, Pillow Block Bearing, Counter, Bevel Gearbox, Swivel Plate and Trunnion Base etc.

Materials:

Lifting Screw	steel C45 (optional: stainless steel)
Worm Gear	phosphor bronze (optional: zinc alloy)
Worm Shaft	heated treated steel C45 (optional: stainless steel)
Bearing	Taper Roll Bearing
Housing	Casting Iron
Oil Sealing	Normal, (optional: high/low temperature oil sealing)

Applications:

Energy & Communications	Solar Panel Tracking Systems, Satellite Dish Tracking
Water Projects & Hydropower Station	Sluice Gates, Water Gates, Penstocks, Tilting Barriers, Raise & Lower Power Station Dampers
Iron & Steel	Heavy Plate Steel Mills on Roll Adjustment, Steel Pipe Mills for Roll Adjustment and Back Stops and Tensioners
Food Processing	Dough Presses, Roll Adjustment, Tunnel Freezer, Curing Ovens, Tensioners, Conveyor Height Adjustment
Civil Engineering	Building Ventilation, Bridge Lifting
Railways	Maintenance Jacks and Railway Carriage Lift
Theatre	synchronized lifting table for Stage Elevator Platforms Creation of Orchestra Pits, Screen Manipulation

Selection guide of NOSEN screw jack,RN series

Packaging & Shipping
Company InformationCompany Introductions
“NOSEN” CZPT robot motor high precision 6.5inch 24V 250W 4N.m 500RPM IP54 100kg load hub wheel motor for AGV is the most professional spiral bevel gearbox, worm gear screw jack manufacturers and suppliers in China. We only produce above 2 power transmission products since 2003. “NOSEN” regular oversea clients areas:EuropeanBelgium, Bulgaria, Denmark, Finland, Germany, Greece, Netherland, Poland, Poland, Spain, Sweden, United KingdomAmericaUnited States, CanadaAsiaIndia,Indonesia,Malaysia,Philippines,Qatar,Russian,Singapore,Thailand,Sri Lanka,Vietnam,Saudi Arabia,Iran,Georgia,Armenia,KuwaitOceaniaAustralia, New ZealandAfricaEgypt, Zambia Our workshop Certification

screwshaft

Screws and Screw Shafts

A screw is a mechanical device that holds objects together. Screws are usually forged or machined. They are also used in screw jacks and press-fitted vises. Their self-locking properties make them a popular choice in many different industries. Here are some of the benefits of screws and how they work. Also read about their self-locking properties. The following information will help you choose the right screw for your application.

Machined screw shaft

A machined screw shaft can be made of various materials, depending on the application. Screw shafts can be made from stainless steel, brass, bronze, titanium, or iron. Most manufacturers use high-precision CNC machines or lathes to manufacture these products. These products come in many sizes and shapes, and they have varying applications. Different materials are used for different sizes and shapes. Here are some examples of what you can use these screws for:
Screws are widely used in many applications. One of the most common uses is in holding objects together. This type of fastener is used in screw jacks, vises, and screw presses. The thread pitch of a screw can vary. Generally, a smaller pitch results in greater mechanical advantage. Hence, a machined screw shaft should be sized appropriately. This ensures that your product will last for a long time.
A machined screw shaft should be compatible with various threading systems. In general, the ASME system is used for threaded parts. The threaded hole occupies most of the shaft. The thread of the bolt occupy either part of the shaft, or the entire one. There are also alternatives to bolts, including riveting, rolling pins, and pinned shafts. These alternatives are not widely used today, but they are useful for certain niche applications.
If you are using a ball screw, you can choose to anneal the screw shaft. To anneal the screw shaft, use a water-soaked rag as a heat barrier. You can choose from two different options, depending on your application. One option is to cover the screw shaft with a dust-proof enclosure. Alternatively, you can install a protective heat barrier over the screw shaft. You can also choose to cover the screw shaft with a dust-proof machine.
If you need a smaller size, you can choose a smaller screw. It may be smaller than a quarter of an inch, but it may still be compatible with another part. The smaller ones, however, will often have a corresponding mating part. These parts are typically denominated by their ANSI numerical size designation, which does not indicate threads-per-inch. There is an industry standard for screw sizes that is a little easier to understand.

Ball screw nut

When choosing a Ball screw nut for a screw shaft, it is important to consider the critical speed of the machine. This value excites the natural frequency of a screw and determines how fast it can be turned. In other words, it varies with the screw diameter and unsupported length. It also depends on the screw shaft’s diameter and end fixity. Depending on the application, the nut can be run at a maximum speed of about 80% of its theoretical critical speed.
The inner return of a ball nut is a cross-over deflector that forces the balls to climb over the crest of the screw. In one revolution of the screw, a ball will cross over the nut crest to return to the screw. Similarly, the outer circuit is a circular shape. Both flanges have one contact point on the ball shaft, and the nut is connected to the screw shaft by a screw.
The accuracy of ball screws depends on several factors, including the manufacturing precision of the ball grooves, the compactness of the assembly, and the set-up precision of the nut. Depending on the application, the lead accuracy of a ball screw nut may vary significantly. To improve lead accuracy, preloading, and lubrication are important. Ewellix ball screw assembly specialists can help you determine the best option for your application.
A ball screw nut should be preloaded prior to installation in order to achieve the expected service life. The smallest amount of preload required can reduce a ball screw’s calculated life by as much as 90 percent. Using a lubricant of a standard grade is recommended. Some lubricants contain additives. Using grease or oil in place of oil can prolong the life of the screw.
A ball screw nut is a type of threaded nut that is used in a number of different applications. It works similar to a ball bearing in that it contains hardened steel balls that move along a series of inclined races. When choosing a ball screw nut, engineers should consider the following factors: speed, life span, mounting, and lubrication. In addition, there are other considerations, such as the environment in which the screw is used.
screwshaft

Self-locking property of screw shaft

A self-locking screw is one that is capable of rotating without the use of a lock washer or bolt. This property is dependent on a number of factors, but one of them is the pitch angle of the thread. A screw with a small pitch angle is less likely to self-lock, while a large pitch angle is more likely to spontaneously rotate. The limiting angle of a self-locking thread can be calculated by calculating the torque Mkdw at which the screw is first released.
The pitch angle of the screw’s threads and its coefficient of friction determine the self-locking function of the screw. Other factors that affect its self-locking function include environmental conditions, high or low temperature, and vibration. Self-locking screws are often used in single-line applications and are limited by the size of their pitch. Therefore, the self-locking property of the screw shaft depends on the specific application.
The self-locking feature of a screw is an important factor. If a screw is not in a state of motion, it can be a dangerous or unusable machine. The self-locking property of a screw is critical in many applications, from corkscrews to threaded pipe joints. Screws are also used as power linkages, although their use is rarely necessary for high-power operations. In the archimedes’ screw, for example, the blades of the screw rotate around an axis. A screw conveyor uses a rotating helical chamber to move materials. A micrometer uses a precision-calibrated screw to measure length.
Self-locking screws are commonly used in lead screw technology. Their pitch and coefficient of friction are important factors in determining the self-locking property of screws. This property is advantageous in many applications because it eliminates the need for a costly brake. Its self-locking property means that the screw will be secure without requiring a special kind of force or torque. There are many other factors that contribute to the self-locking property of a screw, but this is the most common factor.
Screws with right-hand threads have threads that angle up to the right. The opposite is true for left-hand screws. While turning a screw counter-clockwise will loosen it, a right-handed person will use a right-handed thumb-up to turn it. Similarly, a left-handed person will use their thumb to turn a screw counter-clockwise. And vice versa.
screwshaft

Materials used to manufacture screw shaft

Many materials are commonly used to manufacture screw shafts. The most common are steel, stainless steel, brass, bronze, and titanium. These materials have advantages and disadvantages that make them good candidates for screw production. Some screw types are also made of copper to fight corrosion and ensure durability over time. Other materials include nylon, Teflon, and aluminum. Brass screws are lightweight and have aesthetic appeal. The choice of material for a screw shaft depends on the use it will be made for.
Shafts are typically produced using three steps. Screws are manufactured from large coils, wire, or round bar stock. After these are produced, the blanks are cut to the appropriate length and cold headed. This cold working process pressudes features into the screw head. More complicated screw shapes may require two heading processes to achieve the desired shape. The process is very precise and accurate, so it is an ideal choice for screw manufacturing.
The type of material used to manufacture a screw shaft is crucial for the function it will serve. The type of material chosen will depend on where the screw is being used. If the screw is for an indoor project, you can opt for a cheaper, low-tech screw. But if the screw is for an outdoor project, you’ll need to use a specific type of screw. This is because outdoor screws will be exposed to humidity and temperature changes. Some screws may even be coated with a protective coating to protect them from the elements.
Screws can also be self-threading and self-tapping. The self-threading or self-tapping screw creates a complementary helix within the material. Other screws are made with a thread which cuts into the material it fastens. Other types of screws create a helical groove on softer material to provide compression. The most common uses of a screw include holding two components together.
There are many types of bolts available. Some are more expensive than others, but they are generally more resistant to corrosion. They can also be made from stainless steel or aluminum. But they require high-strength materials. If you’re wondering what screws are, consider this article. There are tons of options available for screw shaft manufacturing. You’ll be surprised how versatile they can be! The choice is yours, and you can be confident that you’ll find the screw shaft that will best fit your application.

China Electric Motor Worm Gear Screw Jack Translating Screw With 6500MM Long Stroke screw shaft collar
editor by czh 2023-06-27

China Customized POMNylon Plastic Split Shaft Collar with One Metric Screw ball screw shaft material

Warranty: 3 months
Applicable Industries: Building Material Shops, Machinery Repair Shops, Energy & Mining
Showroom Location: None
Video outgoing-inspection: Provided
Machinery Test Report: Provided
Marketing Type: Ordinary Product
Warranty of core components: 3 months
Core Components: Bearing
Structure: Flexible
Material: POM/Nylon, POM/Nylon
Coatings: Black Oxide
Torque Capacity: 0.1mm
Model Number: Custom
Product Name: Shaft Collar
Tolerance: 0.05-0.1mm
Item: Nylon Shaft Collar
Sample: Available
Types: Plastic Shaft Collar
Sizes: Custom
Name: Split Shaft Collar
Shipping Info: Air Express/Air/Sea
Type: Plastic Set Screw Shaft Collar
After Warranty Service: Online support
Local Service Location: None
Packaging Details: Factory packaging for Customized POM/Nylon Plastic Split Shaft Collar with One Metric Screw
Port: Any sea or air or port in China

Customized POM/Nylon Plastic Split Shaft Collar with One Metric Screw

Products name	POM/Nylon Plastic Shaft Screw
Brand name	OEM
Sizes	As per your drawing
Material	POM/Nylon Plastic
Precision	PO
Sealing	Open
Service	OEM service
Delivery date	Normally ready goods and stock within 15 days,others 30~40days
Feature	Waterproof and anti-drug
Package	Industrial package or according to clients’requirement
Details	Sleeves to install and remove convenient, improve efficiency and reduce the cost of maintenance machinery.

Specifc data sheet of POM/Nylon Plastic Shaft Collar for your reference.

More Products

Screw Shaft Types and Uses

Various uses for the screw shaft are numerous. Its major diameter is the most significant characteristic, while other aspects include material and function are important. Let us explore these topics in more detail. There are many different types of screw shafts, which include bronze, brass, titanium, and stainless steel. Read on to learn about the most common types. Listed below are some of the most common uses for a screw shaft. These include: C-clamps, screw jacks, vises, and more.

Major diameter of a screw shaft

A screw’s major diameter is measured in fractions of an inch. This measurement is commonly found on the screw label. A screw with a major diameter less than 1/4″ is labeled #0 to #14; those with a larger diameter are labeled fractions of an inch in a corresponding decimal scale. The length of a screw, also known as the shaft, is another measure used for the screw.
The major diameter of a screw shaft is the greater of its two outer diameters. When determining the major diameter of a screw, use a caliper, micrometer, or steel rule to make an accurate measurement. Generally, the first number in the thread designation refers to the major diameter. Therefore, if a screw has a thread of 1/2-10 Acme, the major diameter of the thread is.500 inches. The major diameter of the screw shaft will be smaller or larger than the original diameter, so it’s a good idea to measure the section of the screw that’s least used.
Another important measurement is the pitch. This measures the distance between one thread’s tip and the next thread’s corresponding point. Pitch is an important measurement because it refers to the distance a screw will advance in one turn. While lead and pitch are two separate concepts, they are often used interchangeably. As such, it’s important to know how to use them properly. This will make it easier to understand how to select the correct screw.
There are three different types of threads. The UTS and ISO metric threads are similar, but their common values for Dmaj and Pmaj are different. A screw’s major diameter is the largest diameter, while the minor diameter is the lowest. A nut’s major diameter, or the minor diameter, is also called the nut’s inside diameter. A bolt’s major diameter and minor diameter are measured with go/no-go gauges or by using an optical comparator.
The British Association and American Society of Mechanical Engineers standardized screw threads in the 1840s. A standard named “British Standard Whitworth” became a common standard for screw threads in the United States through the 1860s. In 1864, William Sellers proposed a new standard that simplified the Whitworth thread and had a 55 degree angle at the tip. Both standards were widely accepted. The major diameter of a screw shaft can vary from one manufacturer to another, so it’s important to know what size screw you’re looking for.
In addition to the thread angle, a screw’s major diameter determines the features it has and how it should be used. A screw’s point, or “thread”, is usually spiky and used to drill into an object. A flat tipped screw, on the other hand, is flat and requires a pre-drilled hole for installation. Finally, the diameter of a screw bolt is determined by the major and minor diameters.
screwshaft

Material of a screw shaft

A screw shaft is a piece of machine equipment used to move raw materials. The screw shaft typically comprises a raw material w. For a particular screw to function correctly, the raw material must be sized properly. In general, screw shafts should have an axial-direction length L equal to the moving amount k per 1/2 rotation of the screw. The screw shaft must also have a proper contact angle ph1 in order to prevent raw material from penetrating the screw shaft.
The material used for the shaft depends on its application. A screw with a ball bearing will work better with a steel shaft than one made of aluminum. Aluminum screw shafts are the most commonly used for this application. Other materials include titanium. Some manufacturers also prefer stainless steel. However, if you want a screw with a more modern appearance, a titanium shaft is the way to go. In addition to that, screws with a chromium finish have better wear resistance.
The material of a screw shaft is important for a variety of applications. It needs to have high precision threads and ridges to perform its function. Manufacturers often use high-precision CNC machines and lathes to create screw shafts. Different screw shafts can have varying sizes and shapes, and each one will have different applications. Listed below are the different materials used for screw shafts. If you’re looking for a high-quality screw shaft, you should shop around.
A lead screw has an inverse relationship between contact surface pressure and sliding velocity. For heavier axial loads, a reduced rotation speed is needed. This curve will vary depending on the material used for the screw shaft and its lubrication conditions. Another important factor is end fixity. The material of a screw shaft can be either fixed or free, so make sure to consider this factor when choosing the material of your screw. The latter can also influence the critical speed and rigidity of the screw.
A screw shaft’s major diameter is the distance between the outer edge of the thread and the inner smooth part. Screw shafts are typically between two and sixteen millimeters in diameter. They feature a cylindrical shape, a pointy tip, and a wider head and drive than the former. There are two basic types of screw heads: threaded and non-threaded. These have different properties and purposes.
Lead screws are a cost-effective alternative to ball screws, and are used for low power and light to medium-duty applications. They offer some advantages, but are not recommended for continuous power transmission. But lead screws are often quieter and smaller, which make them useful for many applications. Besides, they are often used in a kinematic pair with a nut object. They are also used to position objects.
screwshaft

Function of a screw shaft

When choosing a screw for a linear motion system, there are many factors that should be considered, such as the position of the actuator and the screw and nut selection. Other considerations include the overall length of travel, the fastest move profile, the duty cycle, and the repeatability of the system. As a result, screw technology plays a critical role in the overall performance of a system. Here are the key factors to consider when choosing a screw.
Screws are designed with an external threading that digs out material from a surface or object. Not all screw shafts have complete threading, however. These are known as partially threaded screws. Fully threaded screws feature complete external threading on the shaft and a pointed tip. In addition to their use as fasteners, they can be used to secure and tighten many different types of objects and appliances.
Another factor to consider is axial force. The higher the force, the bigger the screw needs to be. Moreover, screws are similar to columns that are subject to both tension and compression loads. During the compression load, bowing or deflection is not desirable, so the integrity of the screw is important. So, consider the design considerations of your screw shaft and choose accordingly. You can also increase the torque by using different shaft sizes.
Shaft collars are also an important consideration. These are used to secure and position components on the shaft. They also act as stroke limiters and to retain sprocket hubs, bearings, and shaft protectors. They are available in several different styles. In addition to single and double split shaft collars, they can be threaded or set screw. To ensure that a screw collar will fit tightly to the shaft, the cap must not be overtightened.
Screws can be cylindrical or conical and vary in length and diameter. They feature a thread that mates with a complementary helix in the material being screwed into. A self-tapping screw will create a complementary helix during driving, creating a complementary helix that allows the screw to work with the material. A screw head is also an essential part of a screw, providing gripping power and compression to the screw.
A screw’s pitch and lead are also important parameters to consider. The pitch of the screw is the distance between the crests of the threads, which increases mechanical advantage. If the pitch is too small, vibrations will occur. If the pitch is too small, the screw may cause excessive wear and tear on the machine and void its intended purpose. The screw will be useless if it can’t be adjusted. And if it can’t fit a shaft with the required diameter, then it isn’t a good choice.
Despite being the most common type, there are various types of screws that differ in their functions. For example, a machine screw has a round head, while a truss head has a lower-profile dome. An oval-its point screw is a good choice for situations where the screw needs to be adjusted frequently. Another type is a soft nylon tip, which looks like a Half-dog point. It is used to grip textured or curved surfaces.

China Customized POMNylon Plastic Split Shaft Collar with One Metric Screw ball screw shaft material
editor by czh 2023-06-27

China supplier Jsw Extruder Machine Tex160 Screw Shaft Maris Screw Shafts for Petrochemical Factory shaft collar with set screw lowe’s

Product Description

Manufacture Plastic Extruder Shaft For PVC

Production description:

Product name	Twin screw shaft	Brand name	JOINER
Model number	TEX160	Material	WR15E WR30 40CrNiMo
Spline type	involute inner spline	Place of original	ZheJiang , China
Size	Dia 10-120mm/ L 500-900mm	Screw combination	Brick patern construction
Construction	With or without cooling system	LD	36:1 40:1 44:1 48:1
Hardness	HRC44
Surface treatment	vacuum quenching
Certification	ISO9001 2015
Application	Plastic industry Wood plastic inflated Food powder coating
For what machine	Plastic Wood Food Twin Extruder machine
shaft for	APV KOBE OMC KraussMaffei Theysohn Buss Berstorff Toshiba Clextral Labtech USEON Lantai others JSW Leistritz Keya Maris
Our strengths	Competitive costs per unit of production Fast turn round for collection and delivery on refurbished parts Parts available from stock for a wide range of extruder makes Comprehensive inspection procedure on all parts prior to dispatch A time proven quality service Latest manufacturing techniques and metallurgy, ensuring consistent and reliable performance of parts Customized solutions to meet specific needs.

We manufacture screw shafts for co-rotating twin screw extruders ranging from 10 mm to 120 mm /Length 500-900mm and over. With cooling system /without cooling system. Our manufacturing specializes in shafts for twin screw extruders and is optimized for flexible order handling.

Types of shaft:

Single keyway Square keyslot High torque key button Dual keyslot

Involute inner spline Round keyslot Retackle spline Client requirements available

Material

WR15E WR30 40CrNiMo

About our Company

Joiner Machinery Co.,Ltd has several years experience in the manufacture and supply of new and refurbished wear parts for all major makes of twin-screw extruders and the Industries involved in plastics industry, chemical industry, powder coating, food food industry, wood plastic etc..
Through close working relationships with our customers we have been CZPT to fulfill their requirements. Flexibility enables us to design and manufacture standard and bespoke components for unique applications.
Through our highly trained and experienced staff we are CZPT to offer technical support and advice.
Our strengths are based on many years experience supplying the following:
* Competitive costs per unit of production
* Fast turn round for collection and delivery on refurbished parts
* Parts available from stock for a wide range of extruder makes
* Comprehensive inspection procedure on all parts prior to dispatch
* A time proven quality service
* Latest manufacturing techniques and metallurgy, ensuring consistent and reliable performance of parts
* Customized solutions to meet specific needs.

Why choose us?

Packaging Delivery

Packaging Details: Wooden case, Sea-worthy or export standard.
Port: HangZhou
Lead time: 40-50 days after order confirmation.

FAQ

Q: Are you trading company or manufacturer ?

A: We are factory.

Q: Where is your factory located? How can I visit there?

A: Our factory is located in HangZhou, ZheJiang Province, China, 1) You can fly to

HangZhou Airport directly. We will pick you up when you arrive in the airport; All our clients,

from domestic or abroad, are warmly welcome to visit us

Q: What makes you different with others?

A: 1) Our Excellent Service For a quick, no hassle quote just send email to us We

promise to reply with a price within 24 hours – sometimes even within the hour. If you

questions immediately. 2) Our quick manufacturing time For Normal orders, we will

promise to produce within 30 working days. As a manufacturer, we can ensure the delivery time according to the formal contract.

Q: What is your terms of payment ?

A: 1) T/T payment; 2) LC;

Transport Package:	Wood
Trademark:	JOINER
Origin:	Sichuan

Samples:	US$ 500/Piece 1 Piece(Min.Order) \| Request Sample

Customization:	Available \| Customized Request

screwshaft

Screws and Screw Shafts

Machined screw shaft

Ball screw nut

Self-locking property of screw shaft

Materials used to manufacture screw shaft

China supplier Jsw Extruder Machine Tex160 Screw Shaft Maris Screw Shafts for Petrochemical Factory shaft collar with set screw lowe's
editor by CX 2023-04-24

China 1516 single split one piece shaft collar black oxide zinc plated stainless steel with hex socket cap screw with Best Sales

Applicable Industries: Building Material Shops, high Speed RC Model Front and Rear Engine Ball Bearings With Steel Balls & Si3N4 Ceramic Balls Manufacturing Plant, 32216 Textile Bearing 35716 Chinese Factory Good Quality Tapered Roller Bearing 35716 32216 Machinery Repair Shops, high quantity foring cultivator sweep blade,plowe shovel Energy & Mining

shaft collar

Screws and Screw Shafts

Machined screw shaft

Ball screw nut

Self-locking property of screw shaft

Materials used to manufacture screw shaft

China 1516 single split one piece shaft collar black oxide zinc plated stainless steel with hex socket cap screw with Best Sales
editor by czh 2023-03-04

China 0.5HP Hot Sale AC Deep Well Pump Submersible Pump With Low Price double set screw shaft collar

Warranty: 1 Year
Customized support: OEM, ODM, OBM
Model Number: 3QGD 1.2-50-0.37
Application: Drinking water treatment, Industrial Utilities, Irrigation and Agriculture, Washing and Cleaning, Water Distribution, Water Treatment Solutions
Horsepower: 0.5HP
Power Source: Electric
Pressure: /
Structure: SCREW PUMP
Cable Length: 20m
Outlet Size: 1
Voltage: 220V, 220V
Power: 370W
Material: Stainless Steel
Liquid: Clean Water
Motor: 100% Copper Wire
Impeller: AISI304
Feature: Energy Saving
MOQ: 100PCS
Function: Liquid Transfer
Shaft: Stainless Steel Welded Shaft
Pump body: 304stainless Steel
Packaging Details: STRONG CARTON PACKING WITH EXPORT STHangZhouRD. IF EACH MODEL MORE THEN 500PCS CAN MAKE COLORED STRONG CARTON.
Port: HangZhou

Product Paramenters

Type			Motor power			Capacity Q max	Head H max	Outlet	Spead	Length
single phase 220-240V- Hz50	Three phase 380-415V- Hz50	KW	HP	m7h	m	inch	r/min	mm
2QGD1-50-0.37	2QG 1-50-0.37	0.37	0.5	1	50	3/4″	2850	637
3QGD1.2-50-0.37	3QG 1.2-50-0.37	0.37	0.5	1.8	70	1″	2850	560
3QGD1.2-50-0.55	3QG 1.2-70-0.55	0.55	0.75	1.8	80	1″	2850	630

Company Profile Certifications FAQ 1. who are we?We are based in ZHangZhoug, China, start from 2018,sell to Southeast Asia(40.00%),Africa(30.00%),South America(20.00%), 48V 60V 72V 3KW motor with Controller Eastern Europe(10.00%). There are total about 51-100 people in our office.2. how can we guarantee quality?Always a pre-production sample before mass production;Always final Inspection before shipment;3.what can you buy from us?Solar Pump4. why should you buy from us not from other suppliers?Free samples for new customers,Faster delivery;Years of Export Experience;Years of OEM and ODM experience;We are also a high-tech enterprise with professional R&D center.We have strong independent R & D ability.5. what services can we provide?Accepted Delivery Terms: FOB,CFR,CIF,EXW,FAS,CIP,FCA,CPT,DEQ, original ac servo motor drive manufacturers HC-BH571-S2 DDP,DDU,Express Delivery,DAF,DES；Accepted Payment Currency:USD,EUR,JPY,CAD,AUD,HKD,GBP,CNY,CHF;Accepted Payment Type: T/T,L/C,D/P D/A, rapid amortization drive shaft MoneyGram,Credit Card,PayPal,Western Union,Cash,Escrow;Language Spoken:English,Chinese,Spanish,Japanese,Portuguese,German,Arabic,French,Russian,Korean,Hindi, Made in Italy AX Master by Eurocardan cardan shaft driveline agricultural application triangular profile Italian

Lead Screws and Clamp Style Collars

If you have a lead screw, you’re probably interested in learning about the Acme thread on this type of shaft. You might also be interested in finding out about the Clamp style collars and Ball screw nut. But before you buy a new screw, make sure you understand what the terminology means. Here are some examples of screw shafts:

Acme thread

The standard ACME thread on a screw shaft is made of a metal that is resistant to corrosion and wear. It is used in a variety of applications. An Acme thread is available in a variety of sizes and styles. General purpose Acme threads are not designed to handle external radial loads and are supported by a shaft bearing and linear guide. Their design is intended to minimize the risk of flank wedging, which can cause friction forces and wear. The Centralizing Acme thread standard caters to applications without radial support and allows the thread to come into contact before its flanks are exposed to radial loads.
The ACME thread was first developed in 1894 for machine tools. While the acme lead screw is still the most popular screw in the US, European machines use the Trapezoidal Thread (Metric Acme). The acme thread is a stronger and more resilient alternative to square threads. It is also easier to cut than square threads and can be cut by using a single-point threading die.
Similarly to the internal threads, the metric versions of Acme are similar to their American counterparts. The only difference is that the metric threads are generally wider and are used more frequently in industrial settings. However, the metric-based screw threads are more common than their American counterparts worldwide. In addition, the Acme thread on screw shafts is used most often on external gears. But there is still a small minority of screw shafts that are made with a metric thread.
ACME screws provide a variety of advantages to users, including self-lubrication and reduced wear and tear. They are also ideal for vertical applications, where a reduced frictional force is required. In addition, ACME screws are highly resistant to back-drive and minimize the risk of backlash. Furthermore, they can be easily checked with readily available thread gauges. So, if you’re looking for a quality ACME screw for your next industrial project, look no further than ACME.
screwshaft

Lead screw coatings

The properties of lead screw materials affect their efficiency. These materials have high anti-corrosion, thermal resistance, and self-lubrication properties, which eliminates the need for lubrication. These coating materials include polytetrafluoroethylene (PFE), polyether ether ketone (PEK), and Vespel. Other desirable properties include high tensile strength, corrosion resistance, and rigidity.
The most common materials for lead screws are carbon steel, stainless steel, and aluminum. Lead screw coatings can be PTFE-based to withstand harsh environments and remove oil and grease. In addition to preventing corrosion, lead screw coatings improve the life of polymer parts. Lead screw assembly manufacturers offer a variety of customization options for their lead screw, including custom-molded nuts, thread forms, and nut bodies.
Lead screws are typically measured in rpm, or revolutions per minute. The PV curve represents the inverse relationship between contact surface pressure and sliding velocity. This value is affected by the material used in the construction of the screw, lubrication conditions, and end fixity. The critical speed of lead screws is determined by their length and minor diameter. End fixity refers to the support for the screw and affects its rigidity and critical speed.
The primary purpose of lead screws is to enable smooth movement. To achieve this, lead screws are usually preloaded with axial load, enabling consistent contact between a screw’s filets and nuts. Lead screws are often used in linear motion control systems and feature a large area of sliding contact between male and female threads. Lead screws can be manually operated or mortised and are available in a variety of sizes and materials. The materials used for lead screws include stainless steel and bronze, which are often protected by a PTFE type coating.
These screws are made of various materials, including stainless steel, bronze, and various plastics. They are also made to meet specific requirements for environmental conditions. In addition to lead screws, they can be made of stainless steel, aluminum, and carbon steel. Surface coatings can improve the screw’s corrosion resistance, while making it more wear resistant in tough environments. A screw that is coated with PTFE will maintain its anti-corrosion properties even in tough environments.
screwshaft

Clamp style collars

The screw shaft clamp style collar is a basic machine component, which is attached to the shaft via multiple screws. These collars act as mechanical stops, load bearing faces, or load transfer points. Their simple design makes them easy to install. This article will discuss the pros and cons of this style of collar. Let’s look at what you need to know before choosing a screw shaft clamp style collar. Here are some things to keep in mind.
Clamp-style shaft collars are a versatile mounting option for shafts. They have a recessed screw that fully engages the thread for secure locking. Screw shaft clamp collars come in different styles and can be used in both drive and power transmission applications. Listed below are the main differences between these two styles of collars. They are compatible with all types of shafts and are able to handle axial loads of up to 5500 pounds.
Clamp-style shaft collars are designed to prevent the screw from accidentally damaging the shaft when tightened. They can be tightened with a set screw to counteract the initial clamping force and prevent the shaft from coming loose. However, when tightening the screw, you should use a torque wrench. Using a set screw to tighten a screw shaft collar can cause it to warp and reduce the surface area that contacts the shaft.
Another key advantage to Clamp-style shaft collars is that they are easy to install. Clamp-style collars are available in one-piece and two-piece designs. These collars lock around the shaft and are easy to remove and install. They are ideal for virtually any shaft and can be installed without removing any components. This type of collar is also recommended for those who work on machines with sensitive components. However, be aware that the higher the OD, the more difficult it is to install and remove the collar.
Screw shaft clamp style collars are usually one-piece. A two-piece collar is easier to install than a one-piece one. The two-piece collars provide a more effective clamping force, as they use the full seating torque. Two-piece collars have the added benefit of being easy to install because they require no tools to install. You can disassemble one-piece collars before installing a two-piece collar.
screwshaft

Ball screw nut

The proper installation of a ball screw nut requires that the nut be installed on the center of the screw shaft. The return tubes of the ball nut must be oriented upward so that the ball nut will not overtravel. The adjusting nut must be tightened against a spacer or spring washer, then the nut is placed on the screw shaft. The nut should be rotated several times in both directions to ensure that it is centered.
Ball screw nuts are typically manufactured with a wide range of preloads. Large preloads are used to increase the rigidity of a ball screw assembly and prevent backlash, the lost motion caused by a clearance between the ball and nut. Using a large amount of preload can lead to excessive heat generation. The most common preload for ball screw nuts is 1 to 3%. This is usually more than enough to prevent backlash, but a higher preload will increase torque requirements.
The diameter of a ball screw is measured from its center, called the ball circle diameter. This diameter represents the distance a ball will travel during one rotation of the screw shaft. A smaller diameter means that there are fewer balls to carry the load. Larger leads mean longer travels per revolution and higher speeds. However, this type of screw cannot carry a greater load capacity. Increasing the length of the ball nut is not practical, due to manufacturing constraints.
The most important component of a ball screw is a ball bearing. This prevents excessive friction between the ball and the nut, which is common in lead-screw and nut combinations. Some ball screws feature preloaded balls, which avoid “wiggle” between the nut and the ball. This is particularly desirable in applications with rapidly changing loads. When this is not possible, the ball screw will experience significant backlash.
A ball screw nut can be either single or multiple circuits. Single or multiple-circuit ball nuts can be configured with one or two independent closed paths. Multi-circuit ball nuts have two or more circuits, making them more suitable for heavier loads. Depending on the application, a ball screw nut can be used for small clearance assemblies and compact sizes. In some cases, end caps and deflectors may be used to feed the balls back to their original position.

China 0.5HP Hot Sale AC Deep Well Pump Submersible Pump With Low Price double set screw shaft collar
editor by czh 2023-02-27

China Marine Boat 316 Stainless Steel Stern Shaft Tubes Polished Steel Tail Shaft 1/4 shaft collar with set screw

Solution Description

The marine propeller shaft is an important part of the shafting system. We have the stringent management type the planning substance to packaging to make certain the top quality of the shaft

Content List for the stainless steel stern shaft, propeller shaft:

Chemical Part (%)
C	Si	Mn	P	S	Cr	Ni
≤0.07	≤1.00	≤2.00	≤0.35	≤0.30	seventeen.00-19.00	8.00-11.00

Mechanical Houses
Tensile Test			Hardness Test
o b (MPa)	o s (MPa)	o 5(%)	HB	HRB	HV
≥520	≥205	≥40	≤187	≤90	≤200

Yeld Worth Toughness at Large Temperature
Nominal Thickness (mm)	In the course of the following temperature (°C), o .2 (MP) should be not significantly less than
Nominal Thickness (mm)	one hundred	a hundred and fifty	200	250	three hundred	350	four hundred	450	five hundred	550
2-60	171	a hundred and fifty five	one hundred forty four	a hundred thirty five	127	123	119	114	111	106

Allowable Tension of Steel Forgings
Nominal Thickness (mm)	For the duration of the subsequent temperture (°C), the allowable anxiety should be (MPa)
Nominal Thickness (mm)	≤20	100	a hundred and fifty	two hundred	three hundred	400	500	550	600	650	seven-hundred
2-sixty	137	137	137	130	114	107	100	ninety one	64	forty two	27
2-sixty	137	114	103	ninety six	eighty five	seventy nine	seventy four	seventy one	62	42	27

Item Parameters

Specifications for the stern shaft or propeller shaft:

Material: stainless steel 304/316

Processing methods: solid and lathe machining

Proportions: made in accordance to the vessel

Thorough Images

Business Profile

FAQ

Q1. How do you make sure your good quality?

A: All of our goods move rigid multi inspection approach. Every single assembled drive shaft will go through dynamic balance test to steer clear of vibration. We have one hundred% test prior to shipping and delivery.

Q2. What is actually the precise price tag of your products?
A: Remember to speak to us to get the correct price of our products, and the price tag of the items will be fluctuated due to the various buy amount.

Q3. Can you make according to the samples?
A: Of course, we can create by your samples or specialized drawings. We can develop the molds and fixtures. In addition to, we have comprehensive encounter in establishing and modifying the generate shafts as for each customers’ requirements.

Q4. What are your phrases of packing?
A: Normally, we pack our items in neutral packaging. If you have legally registered patent, we can pack the merchandise in your branded boxes soon after obtaining your authorization letters.

Q5. What is your sample plan?
A: We can offer the sample if we have all set components in stock, the sample cost and the courier expense will be compensated by the consumers. Make sure you speak to us to get the accurate sample cost.

US $100-100,000
/ Piece
| 1 Piece

(Min. Order)

###

Material:	Alloy Steel
Load:	Drive Shaft
Journal Diameter Dimensional Accuracy:	Cutomized
Axis Shape:	Crankshaft
Shaft Shape:	Real Axis
Appearance Shape:	Round

###

Customization:	Available \| Customized Request

###

Chemical Component (%)
C	Si	Mn	P	S	Cr	Ni
≤0.07	≤1.00	≤2.00	≤0.35	≤0.30	17.00-19.00	8.00-11.00

###

Mechanical Properties
Tensile Test			Hardness Test
o b (MPa)	o s (MPa)	o 5(%)	HB	HRB	HV
≥520	≥205	≥40	≤187	≤90	≤200

###

Yeld Value Strength at High Temperature
Nominal Thickness (mm)	During the following temperature (°C), o 0.2 (MP) should be not less than
Nominal Thickness (mm)	100	150	200	250	300	350	400	450	500	550
2-60	171	155	144	135	127	123	119	114	111	106

###

Allowable Stress of Steel Forgings
Nominal Thickness (mm)	During the following temperture (°C), the allowable stress should be (MPa)
Nominal Thickness (mm)	≤20	100	150	200	300	400	500	550	600	650	700
2-60	137	137	137	130	114	107	100	91	64	42	27
2-60	137	114	103	96	85	79	74	71	62	42	27

US $100-100,000
/ Piece
| 1 Piece

(Min. Order)

###

Material:	Alloy Steel
Load:	Drive Shaft
Journal Diameter Dimensional Accuracy:	Cutomized
Axis Shape:	Crankshaft
Shaft Shape:	Real Axis
Appearance Shape:	Round

###

Customization:	Available \| Customized Request

###

Chemical Component (%)
C	Si	Mn	P	S	Cr	Ni
≤0.07	≤1.00	≤2.00	≤0.35	≤0.30	17.00-19.00	8.00-11.00

###

Mechanical Properties
Tensile Test			Hardness Test
o b (MPa)	o s (MPa)	o 5(%)	HB	HRB	HV
≥520	≥205	≥40	≤187	≤90	≤200

###

Yeld Value Strength at High Temperature
Nominal Thickness (mm)	During the following temperature (°C), o 0.2 (MP) should be not less than
Nominal Thickness (mm)	100	150	200	250	300	350	400	450	500	550
2-60	171	155	144	135	127	123	119	114	111	106

###

Allowable Stress of Steel Forgings
Nominal Thickness (mm)	During the following temperture (°C), the allowable stress should be (MPa)
Nominal Thickness (mm)	≤20	100	150	200	300	400	500	550	600	650	700
2-60	137	137	137	130	114	107	100	91	64	42	27
2-60	137	114	103	96	85	79	74	71	62	42	27

Screw Sizes and Their Uses

Screws have different sizes and features. This article will discuss screw sizes and their uses. There are two main types: right-handed and left-handed screw shafts. Each screw features a point that drills into the object. Flat tipped screws, on the other hand, need a pre-drilled hole. These screw sizes are determined by the major and minor diameters. To determine which size of screw you need, measure the diameter of the hole and the screw bolt’s thread depth.

The major diameter of a screw shaft

The major diameter of a screw shaft is the distance from the outer edge of the thread on one side to the tip of the other. The minor diameter is the inner smooth part of the screw shaft. The major diameter of a screw is typically between two and sixteen inches. A screw with a pointy tip has a smaller major diameter than one without. In addition, a screw with a larger major diameter will have a wider head and drive.
The thread of a screw is usually characterized by its pitch and angle of engagement. The pitch is the angle formed by the helix of a thread, while the crest forms the surface of the thread corresponding to the major diameter of the screw. The pitch angle is the angle between the gear axis and the pitch surface. Screws without self-locking threads have multiple starts, or helical threads.
The pitch is a crucial component of a screw’s threading system. Pitch is the distance from a given thread point to the corresponding point of the next thread on the same shaft. The pitch line is one element of pitch diameter. The pitch line, or lead, is a crucial dimension for the thread of a screw, as it controls the amount of thread that will advance during a single turn.
screwshaft

The pitch diameter of a screw shaft

When choosing the appropriate screw, it is important to know its pitch diameter and pitch line. The pitch line designates the distance between adjacent thread sides. The pitch diameter is also known as the mean area of the screw shaft. Both of these dimensions are important when choosing the correct screw. A screw with a pitch of 1/8 will have a mechanical advantage of 6.3. For more information, consult an application engineer at Roton.
The pitch diameter of a screw shaft is measured as the distance between the crest and the root of the thread. Threads that are too long or too short will not fit together in an assembly. To measure pitch, use a measuring tool with a metric scale. If the pitch is too small, it will cause the screw to loosen or get stuck. Increasing the pitch will prevent this problem. As a result, screw diameter is critical.
The pitch diameter of a screw shaft is measured from the crest of one thread to the corresponding point on the next thread. Measurement is made from one thread to another, which is then measured using the pitch. Alternatively, the pitch diameter can be approximated by averaging the major and minor diameters. In most cases, the pitch diameter of a screw shaft is equal to the difference between the two.

The thread depth of a screw shaft

Often referred to as the major diameter, the thread depth is the outermost diameter of the screw. To measure the thread depth of a screw, use a steel rule, micrometer, or caliper. In general, the first number in the thread designation indicates the major diameter of the thread. If a section of the screw is worn, the thread depth will be smaller, and vice versa. Therefore, it is good practice to measure the section of the screw that receives the least amount of use.
In screw manufacturing, the thread depth is measured from the crest of the screw to the root. The pitch diameter is halfway between the major and minor diameters. The lead diameter represents the amount of linear distance traveled in one revolution. As the lead increases, the load capacity decreases. This measurement is primarily used in the construction of screws. However, it should not be used for precision machines. The thread depth of a screw shaft is essential for achieving accurate screw installation.
To measure the thread depth of a screw shaft, the manufacturer must first determine how much material the thread is exposed to. If the thread is exposed to side loads, it can cause the nut to wedge. Because the nut will be side loaded, its thread flanks will contact the nut. The less clearance between the nut and the screw, the lower the clearance between the nut and the screw. However, if the thread is centralized, there is no risk of the nut wedgeing.
screwshaft

The lead of a screw shaft

Pitch and lead are two measurements of a screw’s linear distance per turn. They’re often used interchangeably, but their definitions are not the same. The difference between them lies in the axial distance between adjacent threads. For single-start screws, the pitch is equal to the lead, while the lead of a multi-start screw is greater than the pitch. This difference is often referred to as backlash.
There are two ways to calculate the pitch and lead of a screw. For single-start screws, the lead and pitch are equal. Multiple-start screws, on the other hand, have multiple starts. The pitch of a multiple-start screw is the same as its lead, but with two or more threads running the length of the screw shaft. A square-thread screw is a better choice in applications requiring high load-bearing capacity and minimal friction losses.
The PV curve defines the safe operating limits of lead screw assemblies. It describes the inverse relationship between contact surface pressure and sliding velocity. As the load increases, the lead screw assembly must slow down in order to prevent irreversible damage from frictional heat. Furthermore, a lead screw assembly with a polymer nut must reduce rpm as the load increases. The more speed, the lower the load capacity. But, the PV factor must be below the maximum allowed value of the material used to make the screw shaft.

The thread angle of a screw shaft

The angle between the axes of a thread and the helix of a thread is called the thread angle. A unified thread has a 60-degree angle in all directions. Screws can have either a tapped hole or a captive screw. The screw pitch is measured in millimeters (mm) and is usually equal to the screw major diameter. In most cases, the thread angle will be equal to 60-degrees.
Screws with different angles have various degrees of thread. Originally, this was a problem because of the inconsistency in the threading. However, Sellers’s thread was easier to manufacture and was soon adopted as a standard throughout the United States. The United States government began to adopt this thread standard in the mid-1800s, and several influential corporations in the railroad industry endorsed it. The resulting standard is called the United States Standard thread, and it became part of the ASA’s Vol. 1 publication.
There are two types of screw threads: coarse and fine. The latter is easier to tighten and achieves tension at lower torques. On the other hand, the coarse thread is deeper than the fine one, making it easier to apply torque to the screw. The thread angle of a screw shaft will vary from bolt to bolt, but they will both fit in the same screw. This makes it easier to select the correct screw.
screwshaft

The tapped hole (or nut) into which the screw fits

A screw can be re-threaded without having to replace it altogether. The process is different than that of a standard bolt, because it requires threading and tapping. The size of a screw is typically specified by its major and minor diameters, which is the inside distance between threads. The thread pitch, which is the distance between each thread, is also specified. Thread pitch is often expressed in threads per inch.
Screws and bolts have different thread pitches. A coarse thread has fewer threads per inch and a longer distance between threads. It is therefore larger in diameter and longer than the material it is screwed into. A coarse thread is often designated with an “A” or “B” letter. The latter is generally used in smaller-scale metalworking applications. The class of threading is called a “threaded hole” and is designated by a letter.
A tapped hole is often a complication. There is a wide range of variations between the sizes of threaded holes and nut threads, so the tapped hole is a critical dimension in many applications. However, even if you choose a threaded screw that meets the requisite tolerance, there may be a mismatch in the thread pitch. This can prevent the screw from freely rotating.

China Marine Boat 316 Stainless Steel Stern Shaft Tubes Polished Steel Tail Shaft 1/4 shaft collar with set screw
editor by czh 2023-01-06

China First-Class Quality and Superior Double Screw Pet Food Extruder Screws and Shafts shaft collar with set screw

Product Description

Fast Specifics

Merchandise Identify: Initial-Course Quality and Superior Double Screw Pet Food Extruder Screws and Shafts
Materials: W6MO5CR4V2,WR30,316L,Ni60,SAM10,SAM39,WR5,and many others.

Colour: Steel

Exprience: 20 years

Packaging: Wooden Box or Paper Box According to your purchase

Guide Time: 5-60 days

Screw aspects are the primary functioning parts for twin screw extruder which established the quality and output of plastic items.With high quality,the screw aspects guarantee plastic molecular mixing,slicing,spreading as well as reacting between themselves and many others.Very substantial self cleansing functionality guarantee the higher good quality of the total generation line,for this,our organization combiend our experience for years,the deserves about foreign nations and the customer’s use,then take them into motion,created all sorts of suitable processing screw element with affordable parameters,high self cleansing overall performance,use resistance,corrosion-resistance.

We can satisfy your various substance requirements:

According to look design,

In accordance to Material

-For put on software:

Tool Steel:W6Mo5Cr4V2

PM-HIP content:WR5,WR13,WR14,CPM10V,CPM9V.

-For corrosion software:

38CrMoAla

PM-HIP content:WR4,WR13,WR14,CPM10V,CPM9V.

-For wear and corrosion application:

PM-HIP substance:WR13,WR14,CPM10V,CPM9V.

-Other materials:

Stainless Metal:316L,440C and so on.

Through the knowing of customers,recommend the most beneficial content.

Device Metal

W6Mo5Cr4V2 Chemical Composition
	C	SI	Mn	P	S	Cr	Mo	V	W	Cu	Ni
W-%	.88	.35	.three	.571	.003	four.03	four.eighty one	one.86	5.95	.twelve	.24

Crucial Characteristics:

1) Tool metal, the steel has a high hardenability and thermal cracking resistance, the steel consists of a higher content of tungsten,molybdenum,chromium and alum, very good wear resistance, toughness is comparatively weakened, with excellent warmth resistance.
two) Large hardness,Hardenallity HRC up to sixty five.

Co-rotating Twin Screw Aspects for:

-W&P:ZSK-MC

-Theysohn:TSK

-SM:TEK-HS

-Labtech:LTE

-Berstorff:ZE

-Maris:TM-W

-Feddem:FED-MTS

-Leistritz:ZSE/LSB

-APV:MP65

-JSW-TEX

-TOSHLBA:TEM

-KEYA,RuiYA,LANTAI,Umm-N

Creation Process

Packing&Supply

Packing Details: According to your get amount packaging,delivery picket containers,air carton.

Supply Particulars: 5-60days soon after get.

one.Rust-evidence oil processing,

Prevent rust in transit.

two.Oiled paper offers,

Prevent oil dry.

three.Bubble wrap package,

Prevent collosions.

4.Unique foam packaging.

five.Packing

six.Sealing

Our Support

24-hour Hotline

No issue when and the place

to call we can discover our support to you.

Pre-income Consultation

We have 5 product sales people on-line,

and no matter whether you have any concern

can be solved by means of online

interaction,welcome your session.

Right after-income Providers

Receive merchandise have any

queries about the solution,

can look for us,we will assist

you deal with the the 1st time,to your fulfillment.

All ZT maintain spend focus to each action of the particulars,We are hunting ahead to the forge ahead with each other with you!

FAQ

How prolonged does it consider to get my products because I paid for them?

—In accordance to yout order amount,we will give you a reasonable supply date.

Can I get the guarantee of 1 year for totally free?

—If you want the warranty,you should pay for it.If not,do not fear ,we have self confidence in our goods.

How is your after-sale services?

—You will get our support in time as lengthy as you uncover anything incorrect about our generates.Believe us,you deserve the ideal.

What machine does the merchandise implement to?

—Twin Screw Extruder Machine.

To Be Negotiated 400 mm
(Min. Order)

###

Standard:	DIN
Technics:	Forging
Delivery Time:	5-60 Days
Lolor:	Metal
Transport Package:	Wooden Box or Paper Box According to Your Order
Specification:	15.6-250mm

###

Customization:	Available \| Customized Request

###

W6Mo5Cr4V2 Chemical Composition
	C	SI	Mn	P	S	Cr	Mo	V	W	Cu	Ni
W-%	0.88	0.35	0.3	0.023	0.003	4.03	4.81	1.86	5.95	0.12	0.24

###

First-Class Quality and Superior Double Screw Pet Food Extruder Screws and Shafts

###

1.Rust-proof oil processing,

Prevent rust in transit.

2.Oiled paper packages,

Prevent oil dry.

3.Bubble wrap package,

Prevent collosions.

4.Special foam packaging.

5.Packing

6.Sealing

###

24-hour Hotline

No matter when and where

to call we can find our service to you.

Pre-sales Consultation

We have five sales people online,

and whether you have any question

can be solved through online

communication,welcome your consultation.

After-sales Services

Receive products have any

questions about the product,

can look for us,we will help

you deal with the the first time,to your satisfaction.

All ZT keep pay attention to every step of the details,We are looking forward to the forge ahead together with you!

To Be Negotiated 400 mm
(Min. Order)

###

Standard:	DIN
Technics:	Forging
Delivery Time:	5-60 Days
Lolor:	Metal
Transport Package:	Wooden Box or Paper Box According to Your Order
Specification:	15.6-250mm

###

Customization:	Available \| Customized Request

###

W6Mo5Cr4V2 Chemical Composition
	C	SI	Mn	P	S	Cr	Mo	V	W	Cu	Ni
W-%	0.88	0.35	0.3	0.023	0.003	4.03	4.81	1.86	5.95	0.12	0.24

###

1.Rust-proof oil processing,

Prevent rust in transit.

2.Oiled paper packages,

Prevent oil dry.

3.Bubble wrap package,

Prevent collosions.

4.Special foam packaging.

5.Packing

6.Sealing

###

24-hour Hotline

No matter when and where

to call we can find our service to you.

Pre-sales Consultation

We have five sales people online,

and whether you have any question

can be solved through online

communication,welcome your consultation.

After-sales Services

Receive products have any

questions about the product,

can look for us,we will help

you deal with the the first time,to your satisfaction.

All ZT keep pay attention to every step of the details,We are looking forward to the forge ahead together with you!

Screw Shaft Types

A screw shaft is a cylindrical part that turns. Depending on its size, it is able to drive many different types of devices. The following information outlines the different types of screws, including their sizes, material, function, and applications. To help you select the right screw shaft, consider the following factors:
screwshaft

Size

A screw can come in a variety of shapes and sizes, ranging from a quarter to a quarter-inch in diameter. A screw is a cylindrical shaft with an inclined plane wrapped around it, and its main function is to fasten objects together by translating torque into a linear force. This article will discuss the dimensions of screws and how to determine the size of a screw. It is important to note that screw sizes can be large and small depending on the purpose.
The diameter of a screw is the diameter of its shaft, and it must match the inner diameter of its nuts and washers. Screws of a certain diameter are also called machine screws, and they can be larger or smaller. Screw diameters are measured on the shaft underneath the screw head. The American Society of Mechanical Engineers (ASME) standardized screw diameters in 3/50-inch to 16 (3/8-inch) inches, and more recently, sizes were added in U.S. fractions of an inch. While shaft and head diameters are standardized, screw length may vary from job to job.
In the case of the 2.3-mm screw group, the construct strength was not improved by the 1.2-mm group. The smaller screw size did not increase the strength of the construct. Further, ABS material did not improve the construct strength. Thus, the size of screw shaft is an important consideration in model design. And remember that the more complex your model is, the larger it will be. A screw of a given size will have a similar failure rate as a screw of a different diameter.
Although different screw sizes are widely used, the differences in screw size were not statistically significant. Although there are some limitations, screws of different sizes are generally sufficient for fixation of a metacarpal shaft fracture. However, further clinical studies are needed to compare screw sizes for fracture union rates. So, if you are unsure of what size of screw shaft you need for your case, make sure to check the metric chart and ensure you use the right one.
screwshaft

Material

The material of a screw shaft plays an important role in the overall performance of a screw. Axial and central forces act to apply torque to the screw, while external forces, such as friction, exert a bending moment. The torsional moments are reflected in the torque, and this causes the screw to rotate at a higher rate than necessary. To ensure the longevity of the screw, the material of the screw shaft should be able to handle the bending moment, while the diameter of the shaft should be small enough to avoid causing damage.
Screws are made from different metals, such as steel, brass, titanium, and bronze. Manufacturers often apply a top coating of chromium, brass, or zinc to improve corrosion resistance. Screws made of aluminum are not durable and are prone to rusting due to exposure to weather conditions. The majority of screw shafts are self-locking. They are suited for many applications, including threaded fasteners, C-clamps, and vises.
Screws that are fabricated with conical sections typically feature reduced open cross-sectional areas at the discharge point. This is a key design parameter of conical screw shafts. In fact, reductions of up to 72% are common across a variety of applications. If the screw is designed to have a hard-iron hanger bearing, it must be hardened. If the screw shaft is not hardened, it will require an additional lubricant.
Another consideration is the threads. Screw shafts are typically made of high-precision threads and ridges. These are manufactured on lathes and CNC machines. Different shapes require different materials. Materials for the screw shaft vary. There are many different sizes and shapes available, and each one has its own application. In addition to helical and conical screw shafts, different materials are also available. When choosing material, the best one depends on the application.
The life of the screw depends on its size, load, and design. In general, the material of the screw shaft, nut body, and balls and rollers determine its fatigue life. This affects the overall life of the screw. To determine whether a specific screw has a longer or shorter life, the manufacturer must consider these factors, as well as the application requirements. The material should be clean and free of imperfections. It should be smooth and free of cracks or flaking, which may result in premature failure.

Function

The function of a screw shaft is to facilitate the rotation of a screw. Screws have several thread forms, including single-start, double-start and multi-start. Each form has its own advantages and disadvantages. In this article we’ll explore each of them in detail. The function of a screw shaft can vary based on its design, but the following are common types. Here are some examples of screw shaft types and their purposes.
The screw’s torque enables it to lift objects. It can be used in conjunction with a bolt and nut to lift a load. Screws are also used to secure objects together. You can use them in screw presses, vises, and screw jacks. But their primary function is to hold objects together. Listed below are some of their main functions. When used to lift heavy loads, they can provide the required force to secure an object.
Screws can be classified into two types: square and round. Square threads are more efficient than round ones because they apply 0deg of angle to the nut. Square threads are also stronger than round threads and are often used in high-load applications. They’re generally cheaper to manufacture and are more difficult to break. And unlike square threads, which have a 0deg thread angle, these threads can’t be broken easily with a screwdriver.
A screw’s head is made of a series of spiral-like structures that extend from a cylindrical part to a tip. This portion of the screw is called the shank and is made of the smallest area. The shank is the portion that applies more force to the object. As the shaft extends from the head, it becomes thinner and narrow, forming a pointed tip. The head is the most important part of the screw, so it needs to be strong to perform its function.
The diameter of the screw shaft is measured in millimeters. The M8 screw has a thread pitch of 1.25 mm. Generally, the size of the screw shaft is indicated by the major and minor diameter. These dimensions are appended with a multiplication sign (M8x1).
screwshaft

Applications

The design of screws, including their size and shape, determines their critical rotating speeds. These speeds depend on the threaded part of the screw, the helix angle, and the geometry of the contact surfaces. When applied to a screw, these limits are referred to as “permissible speed limits.” These maximum speeds are meant for short periods of time and optimized running conditions. Continuous operation at these speeds can reduce the calculated life of a nut mechanism.
The main materials used to manufacture screws and screw shafts include steel, stainless steel, titanium, bronze, and brass. Screws may be coated for corrosion resistance, or they may be made of aluminium. Some materials can be threaded, including Teflon and nylon. Screw threads can even be molded into glass or porcelain. For the most part, steel and stainless steel are the most common materials for screw shafts. Depending on the purpose, a screw will be made of a material that is suitable for the application.
In addition to being used in fasteners, screw shafts are used in micrometers, drillers, conveyor belts, and helicopter blades. There are numerous applications of screw shafts, from weighing scales to measuring lengths. If you’re in the market for a screw, make sure to check out these applications. You’ll be happy you did! They can help you get the job done faster. So, don’t delay your next project.
If you’re interested in learning about screw sizing, then it’s important to know the axial and moment loads that your screws will experience. By following the laws of mechanics and knowing the load you can calculate the nominal life of your screw. You can also consider the effect of misalignment, uneven loading, and shocks on your screw. These will all affect the life of your screw. Then, you can select the right screw.

China First-Class Quality and Superior Double Screw Pet Food Extruder Screws and Shafts shaft collar with set screw
editor by czh 2022-12-21

China Steel Split Locking Collar ” Clamp Collars Clamping Shaft 12 Aluminum Single Set Screw Split-Shaft-Locking-Collar Square 36mm ball screw shaft diameter

Product Description

HangZhou FRIMA is IATF16949 certificated manufacturer ,located in HangZhou,China.We are specialized in manufacturing custom-made precision Machining Components. We offer a wide range of manufacturing solutions, including machining, and stamping Our engineering team has rich experience in working in this field for many years.
We have professional quality control team which is built up by rich experienced QC & QA. They will monitor each process of production. Each component or part will go through our QA for final inspection and testing. Make sure every product is under customer’s requirement before CZPT customers.
Our focus is to close the gap and provide lower cost manufacturing throughout the world. Sourcing your parts with FRIMA is the closest thing to running your own manufacturing facility in China. We offer extreme flexibility for you and your project needs.

HangZhou FRIMA will provide you with the following benefits and advantages:

·More saving on manufacturing cost.
·State-of-the-art manufacturing facilities.
·On site manufacturing supervision for quality control.
·Bilingual engineers reporting on your project.
·Reasonable short lead time.

Equipments: CNC machining center, CNC Lathe, milling machine, normal lathe, grinding machine, wire-cut machine, height gauge, projector, and other precise ones.
Materials: Aluminum, Alloy steel, Stainless Steel, brass, etc.
About 80% of FRIMAI’s business is exported, and 20% domestic. FRIMAhas very strict quality control request and system based on IATF16949 management system.
Any enquiries and orders together with drawing or sample as well as investments are extremely welcomed. We sincerely wish to cooperate with your company and create brilliance.

Feature of CNC parts
1. Precision Cnc stainless steel parts strictly according to customer’s drawing, packing, and quality request
2. Tolerance: Can be kept at +/-0.005mm
3. The most advanced CMM inspector to ensure the quality
4. Experienced technology engineers and well-trained workers
5. Fast and timely delivery. Speedily&professional service
6. Quality assurance in accordance with PPAP-3 level system inIATF16949

WMeasuring Facilties	Quadratic Element,Height Gauge,Micrometer,Gauge Block,Needle Gauge,Plug gauge,Caliper,Screw Thread Gauge
Machining Facilities	Machining Tolerance(mm)	Mchining Precision(mm)	Qty	Self-owned
CNC Machining Centre	800×500	0.005-0.01	20pcs	Head Plant
CNC Machining Centre	650×500	0.005-0.01	5pcs	Head Plant
CNC Turning	750×40	0.015-0.005	20pcs	Head Plant
Turning	750×250	0.01-0.02	10pcs	Head Plant
Milling	1200×550	0.01-0.02	6pcs	Head Plant
Grinding	160x360x280	0.005-0.01	4pcs	Head Plant
Grinding	300×680	0.01	1pcs	Head Plant
Wire-cutting	400×350	0.01-0.02	4pcs	Head Plant

Material Available for CNC Turning Service

Material	Stainless steel	SS201 SS303 SS304 SS316 17-4PH SUS440C
	Steel	Q235 20#-45# etc
	Brass	C36000(C26800) C37700(HPb59) C38500(HP6 58) C27200(CuzN37)etc
	Iron	1213 12L14 1215 etc
	Bronze	C51000 C52100 C5400etc
	Aluminum	Al6061 Al6063 Al7075 AL5052 etc
	Alloy	A2 D2 SKD11 DF2 XW/5 ASP-23

Terms and Conditions

Our Processing	CNC machining, CNC milling and turning, drilling, grinding, stamping, tapping,
Surface finish	Hard Coating/Black Anodize/ Clear Anodize/ Hard Chrome /Clear Zinc/Plasma Niride
Tolerance	0.005mm
QC System	100% inspection before shipment
Drawing format	CAD / PDF/ DWG/ IGS/ STEP/So
Packaging	Standard package / Carton box or Pallet / As per customized specifications
Testing equipment	CMM (Coordinate Measuring Machine), Height gauge, Caliper, Hardness tester, Roughness tester, Projector machine, Pin/Angle/Block/Plug/Thickness/Thread/Radius gauge, etc.
Trade terms	EXW, FOB, CIF, As per the customer’s request
Shipment Terms	1) 0-100kg: express & air freight priority 2) >100kg: sea freight priority 3) As per customized specifications
Note	All CNC machining parts are custom-made according to the customer’s drawings or samples, with no stock. If you have any CNC machining parts to be made, please feel free to send your kind drawings/samples to us anytime by email.
Surface Finish	Anodized/Zinc/Nickle/ZiNi plating

Our advantage:
11 years one-stop customized metal products factory.

We will complete different processing designs based on customers’ processing needs and combine different processing techniques to
give customers the best solutions such as CNC machining turning milling stamping forging extrusion casting bending welding etc.

ODM/OEM rapid service

We can do it you only need to provide your project drawings and samples and we can customize and manufacture for you.

Provide high-quality products at a competitive price

Customized processing can be obtained within 5 working days to obtain prototypes and small batch production parts to provide customers with
high-quality and low-cost CNC processed products.

US $0.1-1
/ Piece
| 10 Pieces

(Min. Order)

###

Application:	Automotive Industry
Certification:	IATF16949, RoHS, ISO9001
Transport Package:	Each Pack by PE Bag, Then Pack in Carton
Specification:	SS316/S304, Brass, Aluminum
Trademark:	OEM
Origin:	Ningbo China

###

Customization:	Available \| Customized Request

###

WMeasuring Facilties	Quadratic Element,Height Gauge,Micrometer,Gauge Block,Needle Gauge,Plug gauge,Caliper,Screw Thread Gauge
Machining Facilities	Machining Tolerance(mm)	Mchining Precision(mm)	Qty	Self-owned
CNC Machining Centre	800×500	0.005-0.01	20pcs	Head Plant
CNC Machining Centre	650×500	0.005-0.01	5pcs	Head Plant
CNC Turning	750×40	0.015-0.005	20pcs	Head Plant
Turning	750×250	0.01-0.02	10pcs	Head Plant
Milling	1200×550	0.01-0.02	6pcs	Head Plant
Grinding	160x360x280	0.005-0.01	4pcs	Head Plant
Grinding	300×680	0.01	1pcs	Head Plant
Wire-cutting	400×350	0.01-0.02	4pcs	Head Plant

###

Material	Stainless steel	SS201 SS303 SS304 SS316 17-4PH SUS440C
	Steel	Q235 20#-45# etc
	Brass	C36000(C26800) C37700(HPb59) C38500(HP6 58) C27200(CuzN37)etc
	Iron	1213 12L14 1215 etc
	Bronze	C51000 C52100 C5400etc
	Aluminum	Al6061 Al6063 Al7075 AL5052 etc
	Alloy	A2 D2 SKD11 DF2 XW/5 ASP-23

###

Our Processing	CNC machining, CNC milling and turning, drilling, grinding, stamping, tapping,
Surface finish	Hard Coating/Black Anodize/ Clear Anodize/ Hard Chrome /Clear Zinc/Plasma Niride
Tolerance	0.005mm
QC System	100% inspection before shipment
Drawing format	CAD / PDF/ DWG/ IGS/ STEP/So
Packaging	Standard package / Carton box or Pallet / As per customized specifications
Testing equipment	CMM (Coordinate Measuring Machine), Height gauge, Caliper, Hardness tester, Roughness tester, Projector machine, Pin/Angle/Block/Plug/Thickness/Thread/Radius gauge, etc.
Trade terms	EXW, FOB, CIF, As per the customer’s request
Shipment Terms	1) 0-100kg: express & air freight priority 2) >100kg: sea freight priority 3) As per customized specifications
Note	All CNC machining parts are custom-made according to the customer’s drawings or samples, with no stock. If you have any CNC machining parts to be made, please feel free to send your kind drawings/samples to us anytime by email.
Surface Finish	Anodized/Zinc/Nickle/ZiNi plating

US $0.1-1
/ Piece
| 10 Pieces

(Min. Order)

###

Application:	Automotive Industry
Certification:	IATF16949, RoHS, ISO9001
Transport Package:	Each Pack by PE Bag, Then Pack in Carton
Specification:	SS316/S304, Brass, Aluminum
Trademark:	OEM
Origin:	Ningbo China

###

Customization:	Available \| Customized Request

###

WMeasuring Facilties	Quadratic Element,Height Gauge,Micrometer,Gauge Block,Needle Gauge,Plug gauge,Caliper,Screw Thread Gauge
Machining Facilities	Machining Tolerance(mm)	Mchining Precision(mm)	Qty	Self-owned
CNC Machining Centre	800×500	0.005-0.01	20pcs	Head Plant
CNC Machining Centre	650×500	0.005-0.01	5pcs	Head Plant
CNC Turning	750×40	0.015-0.005	20pcs	Head Plant
Turning	750×250	0.01-0.02	10pcs	Head Plant
Milling	1200×550	0.01-0.02	6pcs	Head Plant
Grinding	160x360x280	0.005-0.01	4pcs	Head Plant
Grinding	300×680	0.01	1pcs	Head Plant
Wire-cutting	400×350	0.01-0.02	4pcs	Head Plant

###

Material	Stainless steel	SS201 SS303 SS304 SS316 17-4PH SUS440C
	Steel	Q235 20#-45# etc
	Brass	C36000(C26800) C37700(HPb59) C38500(HP6 58) C27200(CuzN37)etc
	Iron	1213 12L14 1215 etc
	Bronze	C51000 C52100 C5400etc
	Aluminum	Al6061 Al6063 Al7075 AL5052 etc
	Alloy	A2 D2 SKD11 DF2 XW/5 ASP-23

###

Our Processing	CNC machining, CNC milling and turning, drilling, grinding, stamping, tapping,
Surface finish	Hard Coating/Black Anodize/ Clear Anodize/ Hard Chrome /Clear Zinc/Plasma Niride
Tolerance	0.005mm
QC System	100% inspection before shipment
Drawing format	CAD / PDF/ DWG/ IGS/ STEP/So
Packaging	Standard package / Carton box or Pallet / As per customized specifications
Testing equipment	CMM (Coordinate Measuring Machine), Height gauge, Caliper, Hardness tester, Roughness tester, Projector machine, Pin/Angle/Block/Plug/Thickness/Thread/Radius gauge, etc.
Trade terms	EXW, FOB, CIF, As per the customer’s request
Shipment Terms	1) 0-100kg: express & air freight priority 2) >100kg: sea freight priority 3) As per customized specifications
Note	All CNC machining parts are custom-made according to the customer’s drawings or samples, with no stock. If you have any CNC machining parts to be made, please feel free to send your kind drawings/samples to us anytime by email.
Surface Finish	Anodized/Zinc/Nickle/ZiNi plating

Screws and Screw Shafts

Machined screw shaft

Ball screw nut

Self-locking property of screw shaft

Materials used to manufacture screw shaft

China Steel Split Locking Collar
editor by czh 2022-12-07

China Carbon Stainless Steel One Two Piece Set Screw Single Split Collar Shaft Clamp screw shaft coupler

Product Description

Certification	ISO9001:2018;SGS;TS16949
Quality	CNC machine, CNC Turning, CNC Milling, CNC center machine, auto lathe machine, Wire-cutting Machine , CNC Laser cutting machines, CNC bending machines, CNC punching machines, CNC bending machines CNT stamping machine, CNC/auto lathe machine, Drilling machine, Hydraulic machine, Riveting machine, Tapping machine, welding machine, Film attaching machine, etc.
Materials	Aluminum, Steel, SPCC, SGCC,SECC, SPTE, Stainless steel, Brass, Copper, Bronze, ABS, PC, PO, POM, Nylon, etc.
Surface finish	Anodized, Oxide, Plating, Brushing, Polishing, Blackened, Powder coating, Sandblasting, Laser engraving Zn-plating, Ni-plating, Cr-plating, Tin-plating, copper-plating, the wreath oxygen resin spraying, the heat disposing, hot-dip galvanizing, black oxide coating, painting, powdering, color zinc-plated, blue-black zinc-plated, rust preventive oil, titanium alloy galvanized, silver plating, plastic, electroplating, anodizing, etc
Inspection Equipment	CMM, Projection, Calipers, Micro caliper, Thread Micro caliper, Pin gauge, Caliper gauge, Pass meter, Pass meter, etc.
Drawing formation	PDF, CAD/DWG/DXF, IGS/STP etc.

HangZhou Bifu Industrial Co., Ltd. is a comprehensive factory that specialized in fasteners, CNC parts, stamping parts, machinery parts, and so on. Since the establishment of the company, we have passed ISO9001: 2018, SGS, TS16949.
Our factory covers an area of 5,000 square meters and has 58 employees, including 5 R & D personnel and 5 quality inspection personnel.
Major areas of service include automotive, bicycle and motorcycle, industrial automation, agricultural equipment, digital electronics, medical equipment, and so on.
Looking forward to your cooperation.

1. We have Specialized QC testers to check the products quality according to customers’ needs.

2. We have IQC to check the dimensions and surface of the incoming material.

3. We have PQC to inspect full-course during the processing.

4. We have FQC to inspect all the plating products from outsides and make the 100% inspection before the shipments.

FAQ:

Q1: Why choose ZheJiang n?
To provide our customers with first-class services in the supply of quality screws minimizing costs.

Q2: How is quality ensured?
All our processes strictly adhere to ISO9001:2018 procedures. We have strict quality control from producing to delivery. Our company had strong technology support, 80% of our colleagues are master or bachelor’s degree. We have cultivated a group of managers who are familiar with product quality , good at modern concept of management.

Q3: Can You Strictly Follow The Tolerance on The Drawing And Meet The High Precision?
Yes, we can, we can provide high precision parts and make the parts as your drawing.

Q4: How should I order and make payment?
By T/T, for samples 100% with the order; for production, 30% paid for deposit by T/T before production arrangement, the balance to be paid before shipment. negotiation accepted.

Q5: What’s your Delivery Time?
Standard parts: 7-20days
Non-standard parts: 15-25days
We will make the delivery as soon as possible with the guarantee quality

Q6:How to Custom-made (OEM/ODM)?
If you have a new product drawing or a sample, please send to us, and we can custom-made the as your required. We will also provide our professional advices of the products to make the design to be more realized & maximize the performance.

Q7:Which mode of transport would be better?
In general, the product are heavy, we advice to make delivery by sea, Also we respect your views of other transportation as well.

US $0.1-8.8
/ Piece
| 100 Pieces

(Min. Order)

###

Standard Or Nonstandard:	Standard
Shaft Hole:	8-24
Torque:	>80N.M
Bore Diameter:	19mm
Speed:	8000r/M
Structure:	Rigid

###

Samples:	US$ 20/Piece 1 Piece(Min.Order) \| Request Sample

###

Customization:	Available \| Customized Request

###

Certification	ISO9001:2018;SGS;TS16949
Quality	CNC machine, CNC Turning, CNC Milling, CNC center machine, auto lathe machine, Wire-cutting Machine , CNC Laser cutting machines, CNC bending machines, CNC punching machines, CNC bending machines CNT stamping machine, CNC/auto lathe machine, Drilling machine, Hydraulic machine, Riveting machine, Tapping machine, welding machine, Film attaching machine, etc.
Materials	Aluminum, Steel, SPCC, SGCC,SECC, SPTE, Stainless steel, Brass, Copper, Bronze, ABS, PC, PO, POM, Nylon, etc.
Surface finish	Anodized, Oxide, Plating, Brushing, Polishing, Blackened, Powder coating, Sandblasting, Laser engraving Zn-plating, Ni-plating, Cr-plating, Tin-plating, copper-plating, the wreath oxygen resin spraying, the heat disposing, hot-dip galvanizing, black oxide coating, painting, powdering, color zinc-plated, blue-black zinc-plated, rust preventive oil, titanium alloy galvanized, silver plating, plastic, electroplating, anodizing, etc
Inspection Equipment	CMM, Projection, Calipers, Micro caliper, Thread Micro caliper, Pin gauge, Caliper gauge, Pass meter, Pass meter, etc.
Drawing formation	PDF, CAD/DWG/DXF, IGS/STP etc.

US $0.1-8.8
/ Piece
| 100 Pieces

(Min. Order)

###

Standard Or Nonstandard:	Standard
Shaft Hole:	8-24
Torque:	>80N.M
Bore Diameter:	19mm
Speed:	8000r/M
Structure:	Rigid

###

Samples:	US$ 20/Piece 1 Piece(Min.Order) \| Request Sample

###

Customization:	Available \| Customized Request

###

Certification	ISO9001:2018;SGS;TS16949
Quality	CNC machine, CNC Turning, CNC Milling, CNC center machine, auto lathe machine, Wire-cutting Machine , CNC Laser cutting machines, CNC bending machines, CNC punching machines, CNC bending machines CNT stamping machine, CNC/auto lathe machine, Drilling machine, Hydraulic machine, Riveting machine, Tapping machine, welding machine, Film attaching machine, etc.
Materials	Aluminum, Steel, SPCC, SGCC,SECC, SPTE, Stainless steel, Brass, Copper, Bronze, ABS, PC, PO, POM, Nylon, etc.
Surface finish	Anodized, Oxide, Plating, Brushing, Polishing, Blackened, Powder coating, Sandblasting, Laser engraving Zn-plating, Ni-plating, Cr-plating, Tin-plating, copper-plating, the wreath oxygen resin spraying, the heat disposing, hot-dip galvanizing, black oxide coating, painting, powdering, color zinc-plated, blue-black zinc-plated, rust preventive oil, titanium alloy galvanized, silver plating, plastic, electroplating, anodizing, etc
Inspection Equipment	CMM, Projection, Calipers, Micro caliper, Thread Micro caliper, Pin gauge, Caliper gauge, Pass meter, Pass meter, etc.
Drawing formation	PDF, CAD/DWG/DXF, IGS/STP etc.

Lead Screws and Clamp Style Collars

Acme thread

Lead screw coatings

Clamp style collars

Ball screw nut

China Carbon Stainless Steel One Two Piece Set Screw Single Split Collar Shaft Clamp screw shaft coupler
editor by czh 2022-11-26

China aluminum spacers with set screw Double Split Clamping Threaded Shaft Collar extrusion screw shaft

Applicable Industries: Manufacturing Plant, Machinery Repair Shops, Farms, Restaurant, Retail, Construction works
Structure: shaft collar
Material: steel/stainless steel/aluminium, carbon steel, aluminum,stainless steel or as requirement
Coatings: as required
Torque Capacity: 3600N
Model Number: 10mm-40mm
Product name: aluminum spacers Double Split Clamping ThreadedShaft Collar
Surface treatment: Plain, blue plated, white plated, etc
MOQ: 100pcs
Port: HangZhou,HongKong or as request
Precision: 0.571-0.002mm
Size: according to the requirement
certificate: ISO9001-2015,SGS,ROHS
Keywords: Hex Shaft Collar,aluminum spacers with set screw,split shaft collar
Unit price: 0.57-5.2usd/pcs
Packaging Details: 1PLASTIC BAGS+CARTON+PALLET PACKING ( carton size:20cm*20cm*15cm,the total weight of 1 carton will not more than 18kgs) 2ACCORDING TO CUSTOMERS’ REQUIRMENT 3SUITABLE FOR SEA SHIPPING OR AIR SHIPPING
Port: HangZhou

————————————————————————————————————————————-
WORLD-WIDE CUSTOMERS COMMENTS & FEEDBACKHere are some of comments from our world-wide customers.You can check all the comments at our company profile.Please visit click”Company profile”, then “Ratings&Reviews”Then you can see all comments from our clients. [TRUST THAT YOU WILL LIKE OUR SERVICES,QUALITY AND PRICE] aluminum spacers with set screw Double Split Clamping Threaded Shaft CollarClearance Dia.: 1.062″ Bore Dia.: 3/8″ Item: Shaft Collar Width: 3/8″ Screw Material: Steel Screw Size: #6-32 Outside Dia.: 7/8″ Operating Temp. Range: 0 Degrees to 300 Degrees F Material: Black Oxide Steel/Aluminium/Stainless steel
Application: Toy, Automotive, instrument, electrical equipment, furniture, mechanical equipment,daily living equipment, electronic sports equipment, light industry products, etc

Special products

Packaging & ShippingPacking Details

1. Surface Protective Film + Heat Shrink Film
2. EPE Film for Each Piece Film+ Heat Shrink 3. Wooden pallet in extra charge4. As per customers’ requirements.

Our Services1.before service: all the process of technical production deportment and strict quality control system.we can also provide the free sample.
2.middle service :any problem we will take care of it.
3.100% inspection before shipmenrt by micrometer,height gauge,projector measuring machine ,coordinate measuring machine.

The Four Basic Components of a Screw Shaft

There are four basic components of a screw shaft: the Head, the Thread angle, and the Threaded shank. These components determine the length, shape, and quality of a screw. Understanding how these components work together can make purchasing screws easier. This article will cover these important factors and more. Once you know these, you can select the right type of screw for your project. If you need help choosing the correct type of screw, contact a qualified screw dealer.

Thread angle

The angle of a thread on a screw shaft is the difference between the two sides of the thread. Threads that are unified have a 60 degree angle. Screws have two parts: a major diameter, also known as the screw’s outside diameter, and a minor diameter, or the screw’s root diameter. A screw or nut has a major diameter and a minor diameter. Each has its own angle, but they all have one thing in common – the angle of thread is measured perpendicularly to the screw’s axis.
The pitch of a screw depends on the helix angle of the thread. In a single-start screw, the lead is equal to the pitch, and the thread angle of a multiple-start screw is based on the number of starts. Alternatively, you can use a square-threaded screw. Its square thread minimizes the contact surface between the nut and the screw, which improves efficiency and performance. A square thread requires fewer motors to transfer the same load, making it a good choice for heavy-duty applications.
A screw thread has four components. First, there is the pitch. This is the distance between the top and bottom surface of a nut. This is the distance the thread travels in a full revolution of the screw. Next, there is the pitch surface, which is the imaginary cylinder formed by the average of the crest and root height of each tooth. Next, there is the pitch angle, which is the angle between the pitch surface and the gear axis.
screwshaft

Head

There are three types of head for screws: flat, round, and hexagonal. They are used in industrial applications and have a flat outer face and a conical interior. Some varieties have a tamper-resistant pin in the head. These are usually used in the fabrication of bicycle parts. Some are lightweight, and can be easily carried from one place to another. This article will explain what each type of head is used for, and how to choose the right one for your screw.
The major diameter is the largest diameter of the thread. This is the distance between the crest and the root of the thread. The minor diameter is the smaller diameter and is the distance between the major and minor diameters. The minor diameter is half the major diameter. The major diameter is the upper surface of the thread. The minor diameter corresponds to the lower extreme of the thread. The thread angle is proportional to the distance between the major and minor diameters.
Lead screws are a more affordable option. They are easier to manufacture and less expensive than ball screws. They are also more efficient in vertical applications and low-speed operations. Some types of lead screws are also self-locking, and have a high coefficient of friction. Lead screws also have fewer parts. These types of screw shafts are available in various sizes and shapes. If you’re wondering which type of head of screw shaft to buy, this article is for you.

Threaded shank

Wood screws are made up of two parts: the head and the shank. The shank is not threaded all the way up. It is only partially threaded and contains the drive. This makes them less likely to overheat. Heads on wood screws include Oval, Round, Hex, Modified Truss, and Flat. Some of these are considered the “top” of the screw.
Screws come in many sizes and thread pitches. An M8 screw has a 1.25-mm thread pitch. The pitch indicates the distance between two identical threads. A pitch of one is greater than the other. The other is smaller and coarse. In most cases, the pitch of a screw is indicated by the letter M followed by the diameter in millimetres. Unless otherwise stated, the pitch of a screw is greater than its diameter.
Generally, the shank diameter is smaller than the head diameter. A nut with a drilled shank is commonly used. Moreover, a cotter pin nut is similar to a castle nut. Internal threads are usually created using a special tap for very hard metals. This tap must be followed by a regular tap. Slotted machine screws are usually sold packaged with nuts. Lastly, studs are often used in automotive and machine applications.
In general, screws with a metric thread are more difficult to install and remove. Fortunately, there are many different types of screw threads, which make replacing screws a breeze. In addition to these different sizes, many of these screws have safety wire holes to keep them from falling. These are just some of the differences between threaded screw and non-threaded. There are many different types of screw threads, and choosing the right one will depend on your needs and your budget.
screwshaft

Point

There are three types of screw heads with points: cone, oval, and half-dog. Each point is designed for a particular application, which determines its shape and tip. For screw applications, cone, oval, and half-dog points are common. Full dog points are not common, and they are available in a limited number of sizes and lengths. According to ASTM standards, point penetration contributes as much as 15% of the total holding power of the screw, but a cone-shaped point may be more preferred in some circumstances.
There are several types of set screws, each with its own advantage. Flat-head screws reduce indentation and frequent adjustment. Dog-point screws help maintain a secure grip by securing the collar to the screw shaft. Cup-point set screws, on the other hand, provide a slip-resistant connection. The diameter of a cup-point screw is usually half of its shaft diameter. If the screw is too small, it may slack and cause the screw collar to slip.
The UNF series has a larger area for tensile stress than coarse threads and is less prone to stripping. It’s used for external threads, limited engagement, and thinner walls. When using a UNF, always use a standard tap before a specialized tap. For example, a screw with a UNF point is the same size as a type C screw but with a shorter length.

Spacer

A spacer is an insulating material that sits between two parts and centers the shaft of a screw or other fastener. Spacers come in different sizes and shapes. Some of them are made of Teflon, which is thin and has a low coefficient of friction. Other materials used for spacers include steel, which is durable and works well in many applications. Plastic spacers are available in various thicknesses, ranging from 4.6 to 8 mm. They’re suitable for mounting gears and other items that require less contact surface.
These devices are used for precision fastening applications and are essential fastener accessories. They create clearance gaps between the two joined surfaces or components and enable the screw or bolt to be torqued correctly. Here’s a quick guide to help you choose the right spacer for the job. There are many different spacers available, and you should never be without one. All you need is a little research and common sense. And once you’re satisfied with your purchase, you can make a more informed decision.
A spacer is a component that allows the components to be spaced appropriately along a screw shaft. This tool is used to keep space between two objects, such as the spinning wheel and an adjacent metal structure. It also helps ensure that a competition game piece doesn’t rub against an adjacent metal structure. In addition to its common use, spacers can be used in many different situations. The next time you need a spacer, remember to check that the hole in your screw is threaded.
screwshaft

Nut

A nut is a simple device used to secure a screw shaft. The nut is fixed on each end of the screw shaft and rotates along its length. The nut is rotated by a motor, usually a stepper motor, which uses beam coupling to accommodate misalignments in the high-speed movement of the screw. Nuts are used to secure screw shafts to machined parts, and also to mount bearings on adapter sleeves and withdrawal sleeves.
There are several types of nut for screw shafts. Some have radial anti-backlash properties, which prevent unwanted radial clearances. In addition, they are designed to compensate for thread wear. Several nut styles are available, including anti-backlash radial nuts, which have a spring that pushes down on the nut’s flexible fingers. Axial anti-backlash nuts also provide thread-locking properties.
To install a ball nut, you must first align the tangs of the ball and nut. Then, you must place the adjusting nut on the shaft and tighten it against the spacer and spring washer. Then, you need to lubricate the threads, the ball grooves, and the spring washers. Once you’ve installed the nut, you can now install the ball screw assembly.
A nut for screw shaft can be made with either a ball or a socket. These types differ from hex nuts in that they don’t need end support bearings, and are rigidly mounted at the ends. These screws can also have internal cooling mechanisms to improve rigidity. In this way, they are easier to tension than rotating screws. You can also buy hollow stationary screws for rotator nut assemblies. This type is great for applications requiring high heat and wide temperature changes, but you should be sure to follow the manufacturer’s instructions.

China aluminum spacers with set screw Double Split Clamping Threaded Shaft Collar extrusion screw shaft
editor by czh